Don't Be Cheap When It Comes To Painting

Omaha Interior and Exterior Painting
DIY painting projects save you lots of cash (versus hiring a pro), so don't skimp on the paint or painting tools. Cheap paint and tools lead to sub-par results.
Here are 10 ways not to cut corners on your next painting project.

1.Using Cheap Paint

If you find yourself eyeing a discount brand, remember, cheap paint is no bargain. You'll need more of it to cover the same area. Since it won't cover well, you'll have to spend more time to apply extra coats. And after all this, it may not last as long as better quality paint.

2. Buying a Cheap Roller Cover

You hate cleaning rollers, so you figure you'll just buy a cheap cover and throw it away. Guess what? If your time is worth anything, a cheap roller cover is the most expensive tool you can buy. Cheap covers don't hold enough paint, shed fibers on your walls, and in general are a pain to use.

3. Buying Cheap Masking Tape

Don't buy cheap masking tape. More expensive tape is easier to put on, easier to remove and better at sealing out the paint. There are many specialized types of tape to choose from. Some can be left on longer. Some are meant for outdoor use. And others have less aggressive adhesive so you can mask off delicate surfaces.

4. Using a Low Nap Roller on Walls

A 1/4-in.-nap roller cover is good for applying a smooth finish, but the thin nap doesn't hold much paint. A 3/8- or even 1/2-in.-nap roller cover is best. These thicker covers hold more paint, so it's quicker and easier to apply an even coat of paint. Only buy a 1/4-in.-nap cover if you don't want any stipple on the surface.

5. Using the Paint From Different Batches

Don't make the mistake of thinking that you can run to the paint store and grab another gallon and it'll be the same exact color. It might be perfect, but there's also a chance it'll be slightly different. If you have to buy more paint, plan to cover an entire wall with the new batch rather than starting where you left off. Slight variations in color or sheen on adjacent walls aren't noticeable.

6. Wiping Too Much Paint from the Brush

The common practice of wiping the brush on the lip of the paint container after dipping it is a bad one. You end up scraping off too much paint. Instead, dip the bristles an inch or two into the paint. Then slap the brush on the side of the paint container to remove excess paint. The brush will be loaded with just the right amount of paint.

7. Not Buying Enough Paint

We've all done it. The can says a gallon covers 400 sq. ft., and our walls add up to about 800 sq. ft. It seems like 2 gallons should be enough. But in reality, we end up needing two coats, and the paint only covered about 300 sq. ft. on the first coat. Remember, the first coat usually requires more paint, especially over bare drywall. And don't forget to add what you'll need for the second coat. Finally, you'll want to have some paint left over for touch-up or to repaint a wall later if it gets damaged.

8. Letting Friends Help

Friends can help the job go by faster, but they don't always no how to properly prep, roll and cut in. Sometimes you will end up hiring a pro after or redoing the job yourself.

9. Using Plastic Drop Cloths

Plastic doesn't make a very good drop cloth underfoot. It doesn't absorb the paint, so any little drip or spill is more likely to get tracked around. Plus, plastic is slippery, increasing the chance of a fall. Four-foot-wide canvas 'runners' are my favorite drop cloths, but old bed sheets, rosin paper or cardboard also work well.

10. Not Hiring a Pro

Hire Let Me Fix It Handyman Service. If you don't have the patience to do a good prep job, or will have to buy all kinds of equipment that you may never use again, then it makes sense to at least get an estimate for your paint job. It may not cost as much as you think to have it professionally done. And a poorly done DIY job may end you costing you more in the long run.

Featured Posts
Recent Posts
Search By Tags
Follow Us
  • Facebook Basic Square